2031 Single 31-band graphic equalizer
One little button. So much effect.
DbxÂ® Type IIIÂ® Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box.
We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs.
n the box.
We listened to it and were amazed.
The EQs sounded great without it but with it the performance was nothing short of incredible.
Check it out yourself and see.
But hey, Roger wasn't about to stop there.
PeakPlusÂ® Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who.
So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in."
Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0 dbu to plus 20 dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits.
Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs.
You used to have to settle for second best in a reasonably priced EQ but not any more.
With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction.
Check out the dbx 20 Series graphic EQs at your pro audio outfitter.
You'll see, with the 20 Series EQs you get MORE!!!
- Revolutionary instant encode/decode Type IIIÂ® Noise Reduction in-circuit at the push of a button. Increases S/N ratio by up to 20 dB
- Patent-pending PeakPlusÂ® Limiter threshold range from 0 dBu to +24 dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
- An extremely high quality EQ, patent-pending Type III Noise Reduciton, and the elegant new PeakPlus Limiter all in one great sounding box
- Four segment LED bargraph for BOTH Gain Reduction AND Output Level offers the most comprehensive visual feedback available
- Status LEDs offer visual feedback for all settings on the front panel
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
Electronically balanced/unbalanced, RF filtered
Balanced 40 k ohm, unbalanced 20 kohm
Max Input Level:
>+21 dBu balanced or unbalanced
>40 dB, typically >55 dB at 1 kHz
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
mpedance-balanaced/unbalanced, RF filtered
Balanced 200 Ohm, unbalanced 100 Ohm
Max Output Level:
>+21 dBu balanced/unbalanced into 2 kor greater
>+18 dBm balanced/unbalanced (into 600)
20 Hz to 20 kHz, +/-0.5 dB
<10 Hz to >50 kHz, +0.5/-3 dB
109 dB 115 dB
Noise Reduction In:
(+/-6 and +/-15 dB range):
>102 dB, unweighted, ref: +4 dBu, 22 kHz measurement bandwidth
>120 dB, unweighted
Noise Reduction Out:
(+/-6 dB range):
>94 dB, unweighted, ref: +4 dBu, 22 kHz measurment bandwidth
>120 dB, unweighted
Noise Reduction Out:
(+/-15 dB range):
>90 dB, unweighted, ref: +4 dBu, 22 kHz measurement bandwidth
>108 dB, unweighted
THD + Noise:
<0.04%, 0.02% typical at +4 dBu, 1 kHz
Up to 20 dB of dynamic broadband noise reduction
Type III NR:
Activates dbxÂ® Type IIIÂ® Noise Reduction
Bypasses the Graphic Equalizer section in the signal path
Low Cut (recessed):
Activates the 40 Hz 18 dB/octave Bessel high-pass filter
Selects either +/- 6 dB or +/-15 dB slider boost/cut range
Output Level Meter:
4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18 dBu
Gain Reduction Meter:
4-LED bar graph (all Red) at 0, 3, 6, and 10 dB
Type IIIÂ® NR Active:
Red LED Low cut Active:
Low Cut Active:
+/-6 dB range:
+/-15 dB range:
100 VAC 50/60 Hz, 120 VAC 60 Hz
230 VAC 50/60 Hz
3.5" H X 19" W X 7.9" D (8.9 cm x 48.3 cm x 20.1 cm)
8.5 lbs. (3.9 kg)
NĂ¤ytĂ¤ enemmĂ¤n ->