260 Complete equalization & loudspeaker management system, 2 inputs and 6 outputs
Updater note: While new DriveRack 260s from the factory have version 1.02 firmware, there is no practical difference between 1.01 and 1.02. Version 1.02 only has additional code to increase productivity on the production floor.
There is no benefit to the end user.
There is a reason that Tour Sound Professionals and discriminating Audio Contractors choose dbx® DriveRack® products for their high-end tours and installs.
The DriveRack products provide the tools that ensure that the system sounds its very best.
With the introduction of the new 260, the heritage of unrivaled system/loudspeaker control continues.
The 260 capitalizes on the road tested and contractor approved nature of the other products in the DriveRack line.
The 260 provides full bandpass and crossover configurations as well as independent output processing and a full time RTA for live sound applications.
Contractors will appreciate its control inputs for wall-panel logic control and the patent-pending Advanced Feedback Suppression (AFS™).
The DriveRack 260 continues the legacy of DriveRack series, which has been created by the company that has been redefining the standard of signal processing for more than 30 years.
The DriveRack 260 was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface.
This goal has been achieved by offering two independent channels of processing power with a linkable 28-Band Graphic Equalizer, industry-standard dbx stereo compressor module, feedback eliminator and the 120 A Subharmonic Synthesizer on the input, with a six channel output system that includes parametric EQs, PeakStopPlus® limiters (to provide protection against speaker blowouts) and alignment delay. These features combined with the Wizard setup system and complete DriveWare™ GUI control represent a methodical design that is guaranteed to deliver optimal, all-inclusive processing in a completely scalable system.
- Feedback Elimination
- 2.7 Seconds of Alignment and Zone Delay
- RS-232 PC GUI control
- Classic dbx Compression and Limiting
- Graphic and Parametric EQ
- Auto-EQ Function
- Full Bandpass, Crossover, and Routing Configurations
- Auto Gain Control
- Pink Noise Generator and fulltime RTA
- Setup Wizard with JBL speaker and Crown Power Amplifier Tunings
- Security Lockout
- Wall Panel Control Inputs
Number of Inputs (2) Line inputs. (1) RTA Mic input
Connectors (2) Female XLR line inputs. XLR RTA Mic input
Type Electronically balanced/RF filtered
Impedance >40 kohm
Max Input line level +34dBu with input jumpers in +30 position
CMRR >45 dB
RTA Mic Phantom Voltage +15 VDC
RTA Mic EIN <-110 dBu, 22 Hz - 22 kHz, 150 Ohm
Number of Outputs 6
Connectors Male XLR
Type Electronically balanced, RF filter
Impedance 120 Ohms
Max Output Level +22 dBu
Type dbx Type IV® conversion system
Dynamic Range line >114 dB A-weighted,
>112 dB unweighted
Type IV® dynamic range >119 dB, A-weighted, 22 kHz BW
>117 dB, A-weighted, 22 kHz BW
Sample Rate 48 kHz
Dynamic Range 112 dB A-unweighted, 110 dB unweighted
Dynamic Range 110 dB unweighted, >107 dB weighted
THD + N 0.002% typical at +4 dBu, 1 kHz, 0 dB input gain
Frequency Response 20 Hz - 20 kHz, +/-0.5 dB
Interchannel Crosstalk >110 dB, 120 dB typical
Crosstalk input to output >100 dB
Näytä enemmän ->