AKG WMS 40 PRO TRANSFORMER set, SO40 PRO lähetin dynaamiseen mikkiin, SR40 SINGL.
Tätä tuotetta ei ole enää saatavana.
Product not available anymore.
Back to main
WMS 40 PRO TRANSFORMER set tekee langallisesta suosikki mikistäsi langattoman
- SO40 PRO lähettimen dynaamiseen mikkiin
- SR40 SINGLE vastaanottimen
- taajuudet (ISM1)
AKG WMS 40 PRO TRANSFORMER set
The SO 40 Snapon Transmitter allows you to make easily your most favourite mic wireless!
1x SR 40 FLEXX receiver
- Three selectable UHF frequencies for interference-free reception.
- Diversity: maximum transmission reliability even in difficult environments.
The system automatically selects the antenna providing the best signal.
- Adjustable squelch
- Multichannel capability for simultaneous use of up to nine channels (maximum number of channel depends on local frequency plans).
- All-metal case
- High Definition Audio Performance technology ensures the legendary, realistic AKG sound and perfect audio
The receiver shall be a UHF diversity receiver with three selectable frequencies in the 660 MHz to 865 MHz band.
The receiver shall provide an on/off switch, frequency selector switch, and audio level, RF, and power indicators.
The audio bandwidth shall be 35 Hz to 20 kHz, with 0.8% typical THD at 1 kHz.
The typical A-weighted signal/noise ratio shall be 110 dB(A).
The audio output shall be available on a balanced XLR and an unbalanced TS 1/4" jack, adjustable in level, and deliver 500 mV rms at rated deviation.
The receiver shall be housed in a half-rack metal case for easy rack mounting
THD typ. 0,8 % (at 1 kHz)
Signal/noise ratio typ. 110 dB(A)
Audio outputs bal. XLR and unbal. 1/4" jack, output level adjustable, at rated deviation: 500 mV rms.
Power supply 120/230 V AC
Dimensions 200 x 190 x 44 mm (7.8 x 7.4 x 1.7 in.)
Net weight 665 g (1.5 lbs.)
1x SO 40 transmitter
- Professional XLR connector matching all dynamic microphones
- Ultra-light, glass fiber reinforced miniature case
- Integrated charging contacts
- Extremely low operating cost
The SO 40 snapon transmitter is probably the most cost efficient way to upgrade a hardwire microphone for wireless use.
All you have to do is disconnect the microphone cable and plug the snapon transmitter into the XLR connector on the microphone.
The snapon transmitter with its small and light glass fiber reinforced case will add less weight to the microphone than the cable did.
An input gain control lets you match the SO 40 to the microphone output level.
A noiseless on/off switch allows you to mute any microphone with no on/off switch.
Replaceable color code elements allow easy identification of the various microphone channels in any multichannel concert setup.
The transmitter shall be a plug-in transmitter with an XLR connector to match all dynamic microphones.
The transmitter shall provide an integrated on/mute/off switch, input gain control, and battery status LED as well as an integrated antenna to optimize the RF output.
Charging contacts on the plug-in transmitter shall provide both rechargeable and conventional AAA size dry battery powering options.
The audio bandwidth of the transmitter shall be 40 Hz to 20 kHz and it shall use a fixed carrier frequency between 710 MHz and 865 MHz.
The transmitter shall be 98 mm long, weigh 36 grams net without battery, provide an RF output of 5 mW (ERP), and operate for eight hours or longer off a single AAA size battery.
Carrier frequency range 710 MHz to 865 MHz
Audio bandwidth 40 to 20,000 Hz
THD 0.8% typ.
Signal/noise ratio 103 dB (A) typ.
RF output power 5 mW typ. (ERP)
Power supply single 1.5 V AAA size battery
Battery life >10 hours (dry batteries), >5 hours (rechargeable batteries)
Dimensions 22 x 30 x 98 mm / 0.9 x 1.2 x 3.9 in.
Net weight 36 g / 1.3 oz.
Only available in conjunction with a WMS 40 PRO TRANSFORMER set
Näytä enemmän ->